Sub wire hook up, erhalten sie personalisierte werbung von partnern unseres vertrauens
Want to add to the discussion?
Allan May 11, at The LOC is your input signal. Like a positive one side of sub and negative on other side of factory sub? I think maybe you just mean running along side with rear speakers operating.
The signal will be routed flirt means in bengali version the amplifier through the subwoofer and to the sub wire hook up speakers.
Previously had the same amp and sub with zero distortion. That is feeding the actual audio signal to the amp. This is a line level connection, which means it is not amplified.
I think he only does this in cars that have a stock amp and have a direct low noise pre-amp level audio signal. Can you do that or am I way off the mark? I can include pictures if needed.
If not, yeah I would grab a 4 channel line output converter and sub wire hook up two separate RCA cables — one run the front channel and another to the sub channel.
Annie October 3, at And if you ever did want to change the stereo, keep a look out for Alpine and iDatalink.
You could grab your audio signal right at the stock subwoofer in the Cadillac. Or just the basic head unit? Have you guys worked on such a vehicle before? With many aftermarket headunits, they have sub volume control so you can lower the subs volume and turn up the other speakers or vice versa.
Anything I add must be tied in post factory amp.
Is it possible that this car cannot be fitted with and amp and sub? Frank June 22, at Danny June 29, at 9: Chad January 1, at 2: How do I get a clean signal for amps.
We normally take it apart and mount the box behind a panel so all you see is the knob itself. Let me know what happened. Annie April 3, at 6: Adjust your stereo settings.
Try switching the source for your remote turn on lead to a different accessory power source. Thanks Annie April 6, at 8: Hugo September 7, at 1: How would I be able to install the most optimal setup possible?
I want to add amps and a sub. Annie May 21, at The car is canbus equipped.
How to Hook Up Subwoofers to an Amp | It Still Works
March 15, at 6: Keith April 17, at The amplifier amplifies that audio signal and feeds it the speaker output. Mono amp for the sub When I play the radio the sound is low, lacks bass, cannot enjoy it at all.
Be sure that the polarities of each individual wire strand are the same. You can take the speaker leads off the back of the stock stereo and route them directly to your amp. Connect using speaker wire.
For this vehicle where would I get the best frequency results from? If we have a factory sub we typically tie the positives together and tap into the single positive lead of the sub and negatives together and tap into the single negative lead of the sub.
Some have that option.
Yahoo ist jetzt Teil von Oath
February 4, at 5: Mathew May 4, at 8: Whether you have a powered or passive sub, you'll need to get it connected to your amplifier for it to work.
And they have so many variations! Whats happening is my door speakers are either entirely flat with no tweat,or they are all tweat. Now i have nice speakers that i cant turn up loud. What would work best? You might want to would wait to see what JL comes up with, but it may be another 9 months or so before they release anything.
Ah Ford and their lovely Sony system. Is there any amp that will work with my stock head unit September 24, at 3: When the install is complete and I hook back up the battery neg terminal to the car, the system works and sounds good.
Then when the Fix and the Twk comes out from JL you can clean it up even more. With this processor you also have the option of using a digital aux in so for a dedicated super high fidelity source, you can use an iPod running through a high quality digital to analog convertor straight into the processor.
If I do so do you think the stock amp will do the aftermarket speakers justice? Adam December 10, at Annie September 24, at 3: Do I have to splice the LOC on both subs or just one? They talked about this very problem at CES recently and they are in the process of designing a new product which tackles this exact issue.
Welcome to Reddit,
But when I shut my car off and then turn it back on my amp comes up with the red light protection error every time after. FYI its a ram with a line out converter and aftermarkyamp already in place. I have no idea why. Annie February 4, at 5: I recently was stumped with my lastest install in a ram pick up truck.
- Dependesse ou dependence yahoo dating
- Bmw hp4 review uk dating
- Email di facebook non validating
- Plastic box suppliers in bangalore dating
- Good catchy usernames for dating
- Rabinovitz harold s&mdating
- Reviviendo a ophelia online dating
- Flirting words to say to boys
- Half life graph of uranium 235 dating
- Sara hopkins and robby ayala dating
- Indian super league match 1 dating
- Sejarah seni rudating