How to hook up 2 channel car amplifier, car audio defined by a chick
Can that feature be turned off on the stock head unit? Using a multimeter find a wire in the connector in the dash that was formerly on the stock radio that has 12 volts when the how to hook up 2 channel car amplifier is off and this will be your Batt.
How can I hook up 10 speakers to my 4 channel car amplifier
The highs are sharp intolerable. What would work best?
Ben March 23, at 1: If all speakers have the same impedance, the total impedance is the impedance of a single speaker paul carrick brunson flow dating by the total number of speakers.
The amp has both high and low inputs, remote subwoofer control as well as variable bass boost.
Share your voice
OnDemand lists black as negative and white as positive on the stock subs. If you have a power antenna there should be a connection for that on the new stereo and the wiring schematic will tell you which one that is.
Insert the plugs on the other end into the correspondingleft and right input jacks of the amplifier. It acts as if the amp is in parallel mode but I have You can take the speaker leads off the back of the stock stereo and route them directly to your amp. How do you hook up a power amp to a house stereo?
This is a Home stereo amp, it comes with an extended 6 year warranty if you register it, I would check into getting a warranty repair before doing anything to it!
It'll probably be overwhelming. As for the speakers once again a schematic is the best way but you can take fir instance the left front speaker wires from the new stereo with the unit turned on and tuned to a station and through trial and error find the two that feed the left front speaker or Ive heard you can use a 9v battery and listen for a buzz to identify the correct wires, or use the continuity tester on the multimeter to identify the wires.
When the install is complete and I hook back up the battery neg terminal to the car, the system works and sounds good. Basically, you need more professional, more experienced shop to help you.
1 Suggested Answer
Annie April 18, at 1: Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options. Sounds great only one problem when car goes on or off i get an annoying distortion sound on subwoofer.
Mono amp for the sub When I play the radio the sound is low, lacks bass, cannot enjoy it at all. If your using an independent PSU, make sure it's plugged in. If you are working on a car stereo system you can simply disconnect the battery terminals. Let me know what happened. I replaced the stock speakers and tried to get them amped.
The subwoofer is hooked up to the receiver with a single interconnect cable. If my amp does not have a speaker level output and my stereo does not have RCA outputs how do i hook it up? Annie May 21, at Allan May 11, at Had 4 wires going to that one sub. With Audison I had many defective units and it would take months, even over a year in one occasion, to have them repaired or exchanged one of the reasons we stopped carrying them.
I want to keep the look of my truck stock so I may swap out the stock door speakers, tweeters, and center speaker.
I cannot recommend this as your PSU could deep-fry your pasty-white nerdy ass any day of the week. Is there any amp that will work with my stock head unit September 24, at 3: As soon as the speakers were amped up the sound shuts off. I can include pictures if needed. You do not NEED the rca jack For most bass systems, you'll want to choose either a mono single-channel amp or a 2-channel amp.
Choose a video to embed
Like if you have the Bose system? Annie October 3, at Or just the basic head unit? So you can and are supposed to have your LOC installed along side your rear speakers. Here are my questions. For more information read this post on how to set up a subwoofer.
Dave May 14, at 1: Typically the only things that will cause an amp to shut down like that is a bad ground or a signal that is clipping causing the amp to overheat and shut down.
Whats happening is my door speakers are either entirely flat with no tweat,or they are all tweat. Should I tap into wires that input into the bose amp or the output wires and which colors. How would I be able to install the most optimal setup possible? They say the problem is with the factory radio.
SOLVED: How to hook up two amp,one a four channel Directed - Fixya
If not, yeah I would grab a 4 channel line output converter and use two separate RCA cables — one run the front channel and another to the sub channel. I have them in a Honda accord tapped in through both rear trunk speakers currently and they sound great and all but with all this new technology there has to be a way to improve, could you guide me with any way to improve my system when switching it from the Honda to the cadillac?
I like to bring the sub's volume up to the point where I just start to hear the bass filling out the speakers' sound, but some listeners prefer more pronounced bass fullness.